Measurement-computing 200 Series DaqBook Manual do Utilizador

© 1998, 1999, 2000, 2001, 2002 by IOtech, Inc. March 2002 Printed in the United States of AmericaDaqBook User's ManualData Acquisition for Notebo

1-2 Overview02-13-02 Daq SystemsDaqBooks, DaqBoards and Daq PC-CardsDaq products connect to one or more DBKs on their signal input side and a co

Daq Systems 02-13-02Overview 1-3Using DBK Cards and Modules for Signal ConditioningThe DBK signal-conditioning cards and module are designed for

1-4 Overview02-13-02 Daq SystemsReference Notes:➣ The software document modules, DaqView, DaqViewXL, and Post Acquisition DataAnalysis User’s Gu

DaqBook User’s Manual 01-23-02Setup and Startup 2-1Setup and Startup 2For DaqBook/100, /112, /120, /200, /216, /260*This chapter provides instruct

2-2 Setup and Startup 01-23-02 DaqBook User’s Manual(1) Set Jumpers(a) Place the unit on a flat, stable surface. Ensure no power

DaqBook User’s Manual 01-23-02Setup and Startup 2-3JP2 – DAC Reference Voltage and SSH (Simultaneous Sample and Hold)JP2 selects an Internal (d

2-4 Setup and Startup 01-23-02 DaqBook User’s ManualIf connecting your DaqBook to a notebook PC,you can use a WBK20A, PCMCIA Inte

DaqBook User’s Manual 01-23-02Setup and Startup 2-5(d) Select DaqBook/DaqBoard Support. For Windows95/98/Me/NT/2000/XP, select 32-bit.If usin

2-6 Setup and Startup 01-23-02 DaqBook User’s ManualPerformance TestsPerformance tests are intended to test various DaqBook funct

DaqBook User’s Manual01-23-02DaqBook Hardware 3-1A Closer Look at DaqBook Hardware 3DaqBook/100, /112, /120, /200, and /216 ……3-1In General …… 3

DaqBook User’s Manual

3-2 DaqBook Hardware01-23-02DaqBook User’s ManualPerformance FactorsDaqBooks are flexible when it comes to analog input capabilities. The A/D ma

DaqBook User’s Manual01-23-02DaqBook Hardware 3-3Front and Rear Panels Excluding DaqBook/260The following illustrations show the relative loca

3-4 DaqBook Hardware01-23-02DaqBook User’s ManualJumpersProper installation requires that several jumpers and switches be set correctly for your

DaqBook User’s Manual01-23-02DaqBook Hardware 3-5Reference Note:The Power Management section of the DBK Option Cards and Modules User’s Manual(p/n

3-6 DaqBook Hardware01-23-02DaqBook User’s ManualBipolar or Unipolar A/D Operation (JP3)**Hardware Setting For DaqBook/100, DaqBook /112, and Daq

DaqBook User’s Manual01-23-02DaqBook Hardware 3-7Time Base Selection (JP5)JP5 is a 2×3 header that allows you to apply 1 of 3 oscillator-derived f

3-8 DaqBook Hardware01-23-02DaqBook User’s ManualDaqBook ConnectionsTo verify connections, turn ON the power switch by flipping the rocker- switc

DaqBook User’s Manual01-23-02DaqBook Hardware 3-9DaqBookP1 PinoutAnalog I/O(compatible with Metrabyte DAS-16)19 LL SENSE GNDCH0 HI IN 37CH1 HI IN

3-10 DaqBook Hardware01-23-02DaqBook User’s ManualDaqBookP2 PinoutDigital I/OThis P2 interface isavailable on theDaqBook/100, /120,/200, and /260

DaqBook User’s Manual01-23-02DaqBook Hardware 3-11DaqBookP3 PinoutPulse/Frequency/High-SpeedDigital I/OThis P3 interface isavailable on theDaqBook

DaqBook User’s Manual02-14-02 iiiWarranty InformationYour IOtech warranty is as stated on the product warranty card. You may contact IOtech by phone,

3-12 DaqBook Hardware01-23-02DaqBook User’s ManualDaqBook/260The DaqBook/260 is a combination of a DaqBook/200 and a DBK60 expansion chassis. The

DaqBook User’s Manual01-23-02DaqBook Hardware 3-13The rear panel is made of three termination panels with connectors for the various sensors.Hardw

3-14 DaqBook Hardware01-23-02DaqBook User’s Manual4 – Remove termination panelsRemove the two screws mounting each termination panel to the card

DaqBook User’s Manual01-23-02DaqBook Hardware 3-156 – Configure chassis for power sourcesAvoid having more than one power source on the P1 bus. +5

3-16 DaqBook Hardware01-23-02DaqBook User’s Manual12 – Install termination panelsMount the termination panels to the card drawer with two screws

DaqBook User’s Manual01-23-02DaqBook Hardware 3-17Stacking HardwareUsing Dual-Lock Tabs and Splice PlatesFor systems that make use of several data

3-18 DaqBook Hardware01-23-02DaqBook User’s ManualUsing T-Cables&$87,21Turn power OFF to the Daq devices and externally connected equipment w

Daq Systems01-28-02DBK Basics, pg. 1DBK BasicsIntroduction…… 1How Do DBKs Connect to the Data Acquisition Device? …… 2Connecting DBKs to DaqBooks, IS

pg. 2, DBK Basics02-13-02Daq SystemsReference Notes: During software installation, Adobe® PDF versions of user manuals willautomatically install

Daq Systems02-13-02DBK Basics, pg. 3Connecting DBKs to Daq PC-CardsThe Daq PC-Card is only intended for connections to a P1 connector of a single “pa

iv02-14-02DaqBook User’s Manual&$87,21Using this equipment in ways other than described in this manual can causepersonal injury or equipment damag

pg. 4, DBK Basics02-13-02Daq SystemsConnecting DBKs to DaqBoard/2000 Series and cPCI DaqBoard/2000c Series BoardsDaqBoard/2000 Series and cPCI Daq

Daq Systems02-13-02DBK Basics, pg. 5DBK Identification TablesAnalog Output DBKsAnalog OutputProduct Name/Description I/OConectivityDBK2 Voltage Outpu

pg. 6, DBK Basics02-13-02Daq SystemsExpansion and Terminal Panel Connection DBKsThe following DBKs offer provide various expansion and connection

Daq Systems02-13-02DBK Basics, pg. 7Tips on Setting up a Data Acquisition SystemA successful installation involves setting up equipment and setting s

pg. 8, DBK Basics02-13-02Daq Systems10. After software is loaded, remember to set the software parameters as needed for yourapplication. The soft

Daq Systems02-13-02DBK Basics, pg. 9The DIN5 is the system’s basic power connector (see the following figure). The CA-115 is a 6-in. cablewith a plu

pg. 10, DBK Basics02-13-02Daq SystemsDBK30A module - provides power at 14 and 28 VDC with a rated capacity of 3.4 A-hr @ 14 VDC.The DBK30A’s 28 V

Daq Systems02-13-02DBK Basics, pg. 11Calculating Your System’s Power NeedsUse the chart below and the worktable on the next page to ensure your syste

pg. 12, DBK Basics02-13-02Daq SystemsDBK Power Requirement Worktable—DemandDBK Voltage Reference CalculationOptions +15 VDC -15 VDC +5 VDC Quantit

Daq Systems02-13-02DBK Basics, pg. 13Additional ReadingDuring software installation, Adobe® PDF versions of user manuals will automatically install o

DaqBook User’s Manual02-14-02vManual LayoutChapter 1 – Daq Systems, a Brief Overview discusses the “modular concept” associated with DaqBooks,DaqBoard

pg. 14, DBK Basics02-13-02Daq Systems

Appendix A – Specifications, DaqBooks02-14-02A-1Specifications, DaqBooks AGeneralPower ConsumptionDa

A-202-14-02 Appendix A – Specifications, DaqBooksThis page is intentionally blank.

Appendix A – Specifications, DaqBooks02-14-02A-3Analog OutputsChannels: 2Connector: DB37 male, P1Resolution: 12 bitsVoltage Ranges: 0 to 5 VDC wit

A-402-14-02 Appendix A – Specifications, DaqBooks

vi

DaqBook User’s Manual02-14-02viiTable of Contents1 – Daq Systems, a Brief OverviewDaq Systems, the Modular Concept ……1-1DaqBooks, DaqBoards, & Daq

viii

Daq Systems 02-13-02Overview 1-1Daq Systems, a Brief Overview 1Daq Systems, the Modular Concept …… 1-1DaqBooks, DaqBoards, and Daq PC-Cards …… 1-2U